How to Store a Pressure Washer Over Winter

How to store a pressure washer over winter: draining the pump, gun and hose, where to keep it, antifreeze for cold storage and the checks before the first use after a frost.

A coiled black pressure washer hose and a folded grey microfibre towel on a black display stand in front of a silver Volkswagen Polo with frosted windows

To store a pressure washer over winter, drain it: take off the water inlet hose, run the machine dry for about 30 seconds, squeeze the gun's trigger to empty it and remove the high-pressure hose. Keep it somewhere warm and dry. On our Kiam DTLR 2 Pro and DTLR 2 Lite, a machine that must stay where it can freeze gets a little vehicle-grade antifreeze in the pump.

Can frost damage a pressure washer?

Yes. Water left inside the pump, the gun or the hose can freeze, and ice inside a pressure washer can damage it. That is why draining matters more than anything else before a cold night. A machine that is drained and kept warm and dry has nothing in it to freeze, and the DTLR 2 machines are never run with water at or below 0 degrees C.

How do you drain a pressure washer?

Drain it after the last wash before a frost and before any long break. These are the steps for the Kiam DTLR 2 Pro and DTLR 2 Lite.

  1. Rinse the detergent system: if you ran a chemical through the machine, fill its tank with clean water and run it through, as detergent left in the pump can damage it.
  2. Disconnect the water: turn off the tap and take the water inlet hose off the machine.
  3. Run it dry: run the machine with no water supply for about 30 seconds to push the water out of the pump.
  4. Empty the gun: squeeze the trigger on the spray gun until no more water comes out.
  5. Disconnect the hose: take the high-pressure hose off the outlet, let the water run out of it and put it away safely.
  6. Clean the inlet filter: a blocked filter restricts the water flow and lowers the pressure, so rinse it before you put the machine away.
A drained black pressure washer hose coiled on a wall hook above a dry wooden garage shelf
Keep the drained kit somewhere warm and dry, off a cold, wet floor.

Where should you store a pressure washer over winter?

Somewhere warm and dry, such as a heated garage, a utility room or indoors. If the machine has to stay where it can freeze, like an unheated shed or garage, or it will not be used for more than three months, drain it and then pour a small amount of standard vehicle-grade antifreeze into the pump. Keep it off a cold, wet floor, and look over the power cable before you put it away. A damaged cable must be replaced by a qualified person, never repaired at home. In a workshop or detailing bay, a wall mount frame with a hose reel keeps the machine and its hose off the floor and out of the way all winter.

How do you store the gun, lance and hose?

Drained, dry and frost-free, just like the machine. Hold the gun with the nozzle pointing down and squeeze the trigger until it stops dripping, then take off the lance and any snow foam lance. Rinse the snow foam lance through with clean water so no foam dries inside it, and keep the gun and lances indoors with the machine. Coil the hose without kinks once it has drained. Our guide to pressure washer hoses covers hose care, lengths and reels.

What should you check before the first use after a frost?

Warm the machine up and make sure it turns freely before you build up pressure.

  1. Warm it up: if the machine was stored somewhere cold, let it sit in a heated area for several minutes before use.
  2. Check the water: do not use the machine if the water is at or below 0 degrees C, and never feed it water hotter than 50 degrees C.
  3. Free the motor if it sticks: after a long break, limescale can stop the motor impeller turning. Put a screwdriver into the access hole at the rear of the machine, gently turn the impeller back and forth a few times, take the screwdriver out and start up as normal.
  4. Check the filter, hose and cable: look over the inlet filter, the high-pressure hose and the power cable before you connect anything.
  5. Bleed the air: connect the water, switch on and hold the trigger open for a few seconds to let the air out of the hose, then set the pressure.

Winter storage checklist

Each row is a job, when to do it and how.

Job When How
Rinse the detergent system After a wash with chemicals Clean water through the tank and the chemical injection
Drain the machine Before a frost or a long break Inlet hose off, run dry for about 30 seconds, squeeze the trigger
Drain the gun and lances Every time you drain the machine Nozzle down, trigger held until it stops dripping
Protect the pump Stored where it can freeze, or unused for over three months A small amount of vehicle-grade antifreeze in the pump
Store it All winter Warm, dry and off the floor
First use after a frost Before you connect it Several minutes in a heated area, impeller turning freely, filter clean

Which pressure washer kit do we recommend?

Every product here is one we stock, picked for the job named beside it.

  • Kiam DTLR 2 Pro Electric Pressure Washer

    Our pick for a detailing bay or a serious home setup. It delivers 160 bar and 10 litres per minute from a 3.0kW induction motor, and comes with a 15m high-pressure hose, a short trigger gun and a detailing lance.

    £725.00In stock
  • Kiam DTLR 2 Lite Electric Pressure Washer

    The compact option, with 150 bar and 8.45 litres per minute from a 2500W motor. It drains and stores exactly like the Pro.

    £595.00In stock
  • DTLR2 Pro Wall Mount Frame and Hose Reel

    Lifts a DTLR 2 Pro off the floor of a workshop or bay, with an integrated hose reel that keeps the high-pressure hose neatly managed. The machine is sold separately.

    £179.00In stock
  • Kiam DTLR2 Lite Wall Mount Frame and Hose Reel

    The same idea for the DTLR 2 Lite, with a 15 metre high-pressure hose already fitted to the reel.

    £179.00In stock
  • DTLR Professional Short Trigger Gun

    A spare gun with brass internals, a 3/8 male inlet and quarter-inch quick connect nozzles, rated to 260 bar and 60 degrees C.

    £59.95In stock

Common questions

Do you need pump antifreeze for a pressure washer?

Not for a drained machine kept warm and dry. If it will sit somewhere that can freeze, or stay unused for more than three months, put a small amount of standard vehicle-grade antifreeze into the pump after draining it.

Can you leave a pressure washer in a shed over winter?

A drained pressure washer and its coiled hose on a shelf inside a frosty garden shed
In a shed that can freeze, drain the machine and add a little vehicle-grade antifreeze to the pump.

Only once it is drained, and with a little vehicle-grade antifreeze in the pump if the shed can freeze. A warm, dry place is better, and a machine stored cold needs several minutes in a heated area before its first use.

Can you use a pressure washer when it is below freezing?

Not when the water is at or below 0 degrees C. Water also freezes on the car, in the door seals and on the drive, so wait for a day above freezing, as our guide to washing your car in cold weather explains.

Why will a pressure washer not start after the winter?

On the DTLR 2 machines, limescale from a long break can stop the motor impeller turning. Turn it gently back and forth with a screwdriver through the access hole at the rear, then start up as normal. Our guide to the DTLR 2 Pro pressure washer covers its specs and kit.

Need help choosing?

Tell our team where you keep your pressure washer and how often you wash in winter, and we will help you choose a machine, a wall frame and the fittings to go with it. You can also browse our pressure washers and the DTLR by Kiam range.

Still Unsure What You Need?

Tell the TDHQ team about your vehicle, the surface you are working on and the result you want to achieve. Photographs can be uploaded where they help explain the problem.

About the Author

The Drivers HQ

Advice content from the TDHQ team, shaped by the questions customers ask online, in store and through Product Advice.

Ask the team a question