Choose a cutting compound by the deepest defect on the paint. A heavy cut compound such as AutoBead Heavy Cut removes deep scratches and sanding marks up to 1500 grade, a medium cut such as AutoBead Medium Cut clears swirl marks and sanding marks up to 2500 grade, and a fine cut such as AutoBead Finishing Compound takes out light swirls and holograms.
How do heavy, medium and fine cut compounds compare?
Each row is a compound we stock, with the defects and the sanding grade it is made to remove, the machine it suits and what sets it apart. The lower the grit number, the deeper the sanding mark.
| Compound | Cut | Removes | Use with | Notes |
|---|---|---|---|---|
| AutoBead Heavy Cut Compound | Heavy | Deep random scratches, buffer trails and sanding marks up to 1500 grade | Rotary or dual action machine | Silicone free, no fillers, very low dust |
| AutoBead Medium Cut Compound | Medium | Swirl marks and sanding marks up to 2500 grade | Rotary or dual action machine | Also works as a one-step correction polish |
| AutoBead Finishing Compound | Fine | Light swirls, holograms and 3000 grit sanding marks | Rotary or dual action machine, or by hand | Leaves no marks or trails, even on softer paint |
| Menzerna Super Heavy Cut Compound 300 Green Line | Heavy, rated cut 10 and gloss 6 out of 10 | Sanding marks of 1200 grit, with a lambswool pad | Rotary at 800 to 1,500 rpm, or orbital | Solvent-free, no fillers or silicones |
| CarPro ClearCut | Heavy | Scratches as deep as P1000 | Dual action, or rotary at up to 1,000 to 1,200 rpm | Very little dust, no wax, fillers or silicone |
| Sonax ProfiLine CutMax | Heavy, rated cut 6 and gloss 4 out of 6 | Sanding marks of P1000 and finer | Rotary machine | Low dust, used on a hard foam or lambswool pad |
| Menzerna Medium Cut Polish 2000 | Medium, rated cut 5 and gloss 6 out of 10 | Slight to moderately deep scratches and car wash scratches | Rotary at 1,250 rpm, or orbital | Clears the marks a heavier compound leaves |
| Menzerna Medium Cut Polish 2500 | Medium, rated cut 5 and gloss 7 out of 10 | Moderately deep scratches and signs of use | Rotary at 1,250 rpm, orbital or by hand | The glossier of the two Menzerna medium polishes |

How do you choose between heavy, medium and fine cut?
Start with the gentlest compound that removes the defect, and only step up when it does not. Look at the paint under a strong light. Fine swirls and holograms need no more than a fine cut finishing compound. Swirl marks you can see in daylight, or light sanding marks, call for a medium cut. Deep random scratches, buffer trails and sanding marks from 1500 grit paper need a heavy cut, followed by a medium or fine compound to bring the gloss back.
Which cutting compound removes deep scratches?
A heavy cut compound. AutoBead Heavy Cut removes sanding marks up to 1500 grade, Menzerna 300 Green Line removes 1200 grit sanding marks with a lambswool pad, and CarPro ClearCut and Sonax CutMax both take out P1000 marks. A scratch that catches your fingernail can be deeper than any compound can level, so read our guide to removing scratches from car paint before you start.
Which cutting compound should a beginner use?
A medium cut on a dual action machine is where we suggest you start. AutoBead Medium Cut Compound is made to work as a one-step correction polish, so one bottle and one pad clear most swirl marks and leave a high gloss finish without a separate finishing stage. Work an area no bigger than six times the size of the pad, keep the pressure light to medium and wipe off the residue as soon as a clear film appears.
Can you use cutting compound by hand?
Only the finer ones. AutoBead Finishing Compound can go on by hand as well as by machine, and Menzerna 2500 can be worked by hand with medium pressure in circular motions. The heavy compounds and AutoBead Medium Cut are made for a rotary or dual action machine, and Sonax CutMax for a rotary machine. By hand you will refine light swirls, but you will not remove deep scratches or sanding marks.
Which heavy cut compounds do we recommend?
Every product here is one we stock, picked for the job named beside it.
Our first pick for deep random scratches, buffer trails and sanding marks up to 1500 grade. Its diminishing abrasives break down as you work, to a finish that needs very little refining. It is silicone free with no fillers and very low dust, suits all paint types and is used on a rotary or dual action machine.
Menzerna Super Heavy Cut 300 Green Line
The 1 litre bottle of a compound rated cut 10 and gloss 6 out of 10. With a lambswool pad it removes 1200 grit sanding marks, and it is solvent-free with no fillers or silicones. Use it on a rotary machine at 800 to 1,500 rpm or on an orbital machine.
CarPro ClearCut Rapid Cutting Compound
A fast-cutting compound that removes scratches as deep as P1000 with very little dust and no wax, fillers or silicone. It suits a two-step correction on any paint, or a single step on many medium to hard paints. On a dual action machine run it at medium to high speed, and on a rotary keep to 1,000 to 1,200 rpm.
Sonax PROFILINE CutMax Heavy Cut Compound
An abrasive polish for rotary machines, rated cut 6 and gloss 4 out of 6, for heavily weathered, scratched or sanded paint. It removes sanding marks of P1000 and finer with low dust, on a hard foam pad or a lambswool pad.
AutoBead Downforce Foam Pads Heavy Cut
The pad to pair with a heavy compound on a dual action or rotary machine. The foam stays firmer for longer under heat, the dense backing foam gives more downward pressure and better rotation, and the rubber-like backing stops polish reaching the hook and loop.
Which medium and fine cut compounds do we recommend?
These take out swirl marks and lighter defects, and they refine the paint after a heavy cut.
Our pick for swirl marks, imperfections and sanding marks up to 2500 grade. It also works as a one-step correction polish and leaves a high gloss finish. It is silicone free and bodyshop safe with no fillers, for a rotary or dual action machine.
An ultra-fine compound for light swirls, holograms and 3000 grit sanding marks. It leaves no marks or trails, even on softer paint, finishes to a high gloss and can be used by machine or by hand.
Menzerna Medium Cut Polish 2000
The 1 litre bottle, rated cut 5 and gloss 6 out of 10, for slight to moderately deep scratches and car wash scratches. It quickly clears the marks a heavier compound leaves behind and contains no silicones or fillers. Use a medium cut foam pad on a rotary machine at 1,250 rpm or on an orbital machine.
Menzerna Medium Cut Polish 2500
The 1 litre bottle, rated cut 5 and gloss 7 out of 10, for moderately deep scratches with more gloss than the 2000. It contains no silicones or fillers, suits all car paint coats and can be worked by rotary, orbital machine or by hand.
For the Koch-Chemie polishes, including Micro Cut M2.02, see our guide to Koch-Chemie polishes.
Do you need to polish after compounding?
Usually, yes. A heavy compound removes the defect, then a finer compound takes out the haze it leaves and brings the gloss back. After AutoBead Heavy Cut, refine with AutoBead Medium Cut or the Finishing Compound. CarPro ClearCut can finish in a single step on many medium to hard paints.
- Prepare: wash and dry the car and decontaminate the paint, so the pad only meets clean paint.
- Test: try the gentlest compound on a small area first and step up only if the defect stays.
- Compound: spread the compound at low speed over an area no bigger than six times the pad, then raise the speed and work in crosswise passes with light to medium pressure until a clear film appears.
- Refine: follow a heavy cut with a medium or fine compound on a softer pad.
- Protect: wipe off the residue with a microfibre towel and protect the corrected paint.
Common questions

Does cutting compound remove clear coat?
Yes, a very thin layer of it. A compound levels the paint by removing a thin layer around the defect, which is why you start with the gentlest compound that works and stop as soon as the defect has gone.
What is the difference between compound and polish?
A compound cuts deeper to remove defects, and a polish refines the finish and adds gloss. Our guide to compound vs polish explains the difference in full.
Which pad goes with which compound?
Pair a heavy compound with a heavy cut foam pad or a wool pad, and a medium or fine compound with a softer pad. Our polishing pads guide matches each pad to the job.
Which compound removes 1500 or 2000 grit sanding marks?
For 1500 grit marks, AutoBead Heavy Cut Compound is made to remove sanding marks up to 1500 grade. Menzerna 300 Green Line removes 1200 grit marks with a lambswool pad, and CarPro ClearCut and Sonax CutMax remove P1000 marks, so all three also handle the finer 1500 and 2000 grit marks. Then refine with AutoBead Medium Cut, which removes marks up to 2500 grade, or with the Finishing Compound for 3000 grit marks.
How big an area should you compound at once?
No bigger than about six times the size of your pad. Spread the compound at low speed first, then raise the speed and work in crosswise passes until a clear film appears, and clean or blow out the pad often while you work.
Need help choosing?
Tell our team what is on your paint and which machine you use, and we will help you pick a compound and a pad. You can also browse our medium cut compounds and finishing polishes.